OilLab 6000​

Standards

ASTM D93 procedures A, B, CDIN EN 22719IP 34ISO 2719

CE marked

  

Subject 

Flash Point on petroleum products, gas oils, fuel oils, lubrificants, biodiesel. Suitable for flash point detection on different substances, waste materials, solvents…

 

Measuring Pensky Martens Principle

The sample is heated and stirred at specified rates, using one of three defined procedures (A, B, or C). An ignition source is directed into the test cup at regular intervals with simultaneous interruption of the stirring, until a flash is detected.

 

Measuring Parameters

  • Temperatures: in °C / °F

  • Measuring range: 0°C … +420°C

  • Resolution: 0.01 °C

  • Accuracy: ± 0.1 °C

  • Repeatability / Reproducibility: as per standards methods or better

 

Measuring Temperature Devices

  • Sample temperature: PT100 sensor completely made in stainless steel resistant to corrosion and shock resistant

  • Bath temperature: PT100 sensor

 

Pressure sensor

  • Built-in sensor with automatic correction of results to a barometric pressure of 101.3 kPa automatically performed by the software at the end of analysis

 

Detection system 

  • A single multi-detector combines the ionization detector and the thermal detector

 

Double ignition system

 

Gas

Ectrical ignitor

Heater

 

Electrical heating with heating rates as per procedures A, B, C

Stirrer

 

An electric motor drives the stirring of the product

Stirring speed as per selected procedures A, B, C

Cooling system

 

Built-in forced air fan

Safety Devices

 

Automatic diagnostic in case of breakage of the sample temperature probe and thermal sensors

Automatic fire detection system

Overheating protection with auto shut off during the test

Gas valve for closing the gas supply (max 30 mBar), at the end of the test

Fire Extinguisher

 

Automatic fire detection and extinguisher system

Software Features

 

All analytical parameters recorded

Customizable analysis parameters and methods

Customizable results report

Printable graphs and results

The software includes:

Analysis Menu

 

Automatic execution of the analysis in accordance to the selected procedure (Standard method as per ASTM / IP / ISO / EN / DIN… norms of reference as well as costumized procedures)

Automatic handling of samples with unknown flash point

Display in real time of all the analysis parameters and status

Fields for introduction of operator and product name

Expected flash point temperature programmable

Audible alarm and displayed messages at the end of the analysis and in case of errors and/or malfunctions

Configuration menu with up to 20 preset samples and expected flash point

Automatic barometric correction of results

Diagnostic Menu

 

Direct access to all analog, digital, inputs and outputs

Selectable value displaying: °C / Volt

Calibration Menu

 

Automatic calibration of each temperature probe

Up to 100 calibration points (standard with 5 and dynamic with up to 100 points)

Programmable calibration frequency with selectable validity period and notice/lock-down at expiration date

Last calibration date referred to each single probe displayed and relevant data printable

Display of calibration diagram

Data Utilities

 

Archive viewer for files recall

All analysis stored in Excel® compatible format

LIMS compatible

Access via password to the following menu:

 

calibration

program settings

selection ignitor type

Calibration:

 

comparative with reference thermometer and barometer

selection calibration due date

automatic diagnostic in case of faulty of the temperature and thermal sensors

Analysis storage:

 

storage capacity for more than 65.000 analysis

export of test results files in the most common formats Excel and PDF

 

Lin-Tech algorithm temperature ramp and auto-adapt for any type of sample

Double Flash detection (by thermal sensor and ionization ring simultaneous)

Rapid test selection between electrical ignitor and gas ignitor

Automatic barometric correction of the results via a built-in barometer

LIMS communication capable

 

Reading interval of PT100 sample from 0 to 450 °C with resolution 0.01 °C

Reading interval of PT100 bath from 0 to 450 °C with resolution 0.01 °C

Double ignition system: gas and / or electrical ignitor

Fully automatic arm that can be brought into three positions: cleaning, testing and idling time

Integrated Touch Screen Panel PC

 

TFT/LCD 8.4"

Resolution 1024 × 768, 16.2 M colours

2 × USB ports for connection to an external printer

1 × ethernet port for LAN and LIMS network

Electrical Supply

 

220V ± 15% / 50 to 60 Hz

115V ± 15% / 60 Hz

Ambient Temperature

 

Max 35°C

H.R. 80%

Dimensions

 

width 37 cm

depth 52 cm

height 32 cm

Weight

 

30 Kg

Accessories / Spare Parts

 

LAB-6000/05-23: heater collar

LAB-6000/06-21: gas valve

LAB-6000/07-01: electrical ignitor

LAB-6000/07-03: micro switch

LAB-6000/07-04: handle

LAB-6000/07-05: gas ignitor

LAB-6000/08-12: PT100 product

LAB-6000/08-13: detection / ionisation cable

LAB-6000/08-14: PT100 Bath

LAB-6000/09-04: gas reducer

LAB-6000/09-05: calibrated brass crucible

LAB-6000/10-04: PCB fuses, box of 10

LAB-6000/11-02: stirrer belt

LAB-6000-118: fire extinguisher system

Calibration Tools

 

OilLab 80: calibration decade box – PT100 simulator

OilLab 91: set of connectors and cables for OilLab 6000

Alternative Products

 

A sentence here about related products with image links below to products you want customer to consider. 

SUBMIT

Name:

This field is required.

Thank You for your enquiry.

Your information has been sent successfully.  One of the Crea Laboratory technologies Team will be in contact with your shortly. 

 

If your enquiry is urgent, please call us on 1300 552 725

Email:

This field is required.

Phone:

This field is required.

Industry:

This field is required.

Company Name:

This field is required.

Address:

This field is required.

Post Code:

Country:

This fi.